IV3100_130-320_M7_Proportional-Valve_Standard_Euro12_Euro67
Source file: IV3100_130-320_M7_Proportional-Valve_Standard_Euro12_Euro67_20260501. Configuration: DI32 / DO32 / TO9 / TI1+9 / AI4 / AO4 / RDO6.
Main Board IO
Digital Input DI (32 points)
| Point | Name |
|---|---|
| DI1 | Mechanical Safety Detection |
| DI2 | Safety Door 2 (NO) |
| DI3 | Core A Advance End |
| DI4 | Core A Retreat End |
| DI5 | Core B Advance End |
| DI6 | Core B Retreat End |
| DI7 | Mold Close End |
| DI8 | Mold Adjust Advance End |
| DI9 | Mold Adjust Retreat End |
| DI10 | — |
| DI11 | Injection Guard |
| DI12 | Ejector Retreat End |
| DI13 | ROB Robot |
| DI14 | Carriage Advance End |
| DI15 | Rear Safety Door (Reverse Logic) (NC) |
| DI16 | Oil Filter Detection |
| DI17 | Screw Speed Detection |
| DI18 | Mold Adjust Photocell |
| DI19 | Detection Photocell 1 |
| DI20 | Thread A Photocell |
| DI21 | Safety Door (Reverse Logic) (NC) |
| DI22 | Core C Advance End (Reserved) |
| DI23 | Core C Retreat End (Reserved) |
| DI24 | Lubrication Detection |
| DI25~DI31 | — |
| DI32 | Special Input 1 (Cycle Start Button Reserved) |
Digital Output DO (32 points)
| Point | Name |
|---|---|
| DO1 | *Mold Close |
| DO2 | *Differential |
| DO3 | *Mold Open |
| DO4 | Injection |
| DO5 | Injection Retreat |
| DO6 | Recovery |
| DO7 | Carriage Advance |
| DO8 | Carriage Retreat |
| DO9 | Ejector Advance |
| DO10 | Ejector Retreat |
| DO11 | Core A Advance |
| DO12 | Core A Retreat |
| DO13 | Mold Adjust Advance |
| DO14 | Mold Adjust Retreat |
| DO15 | Core B Advance |
| DO16 | Core B Retreat |
| DO17 | IMM Safety Door |
| DO18 | Recovery Back Pressure |
| DO19 | Blow 1 |
| DO20 | Recovery Zero Back Pressure |
| DO21 | — |
| DO22 | — |
| DO23 | Alarm |
| DO24 | Valve 1-1 / Nozzle Needle Valve (PET Mode) |
| DO25 | Mold Close Safety |
| DO26 | Auto Light |
| DO27 | Manual Light |
| DO28 | Blow 2 |
| DO29 | Core C Advance (Reserved) |
| DO30 | Core C Retreat (Reserved) |
| DO31 | Hopper Cooling (Reserved) |
| DO32 | Oil Temp Cooling (Reserved) |
Extension DO (33~48)
| Point | Name |
|---|---|
| DO33 | Heater 1 |
| DO34~DO38 | Heater 2 ~ Heater 6 |
| DO39 | Heater 7 |
| DO40~DO42 | — |
| DO43 | Lubrication |
| DO44 | IMM Robot |
| DO45 | TC1 Heater ON (Master Heater ON) |
| DO46 | — |
| DO47 | Motor ON |
| DO48 | — |
Analog AI / AO
| Point | Name | Note |
|---|---|---|
| AI1 | Injection | |
| AI2 | Mold Open/Close | |
| AI3 | Ejector | |
| AI4 | — | |
| PV1± | — | |
| FV1± | — | (Electric Recovery) |
| P2± | Proportional Back Pressure | |
| FV2± | Proportional Valve |
Temperature TI / TO
| Point | Note |
|---|---|
| TI0 | Oil Temp |
| TI1~TI2 | — |
| TI3 | 130-170 (incl.) Models 1-5, 5 zones |
| TI4 | 218-320 (incl.) Models 1-6, 6 zones |
| TI5~TI9 | — |
| TO1~TO2 | — |
| TO3 | 130-170 (incl.) Models 1-5, 5 zones |
| TO4 | 218-320 (incl.) Models 1-6, 6 zones |
| TO5~TO9 | — |
IO Extension Board · Euro 67 Robot
| Ext DI | Signal | Ext DO | Signal |
|---|---|---|---|
| 33 / E01 | — | 49 / E01 | — |
| 34 / E02 | — | 50 / E02 | — |
| 35 / E03 | — | 51 / E03 | — |
| 36 / E04 | — | 52 / E04 | — |
| 37 / E05 | — | 53 / E05 | — |
| 38 / E06 | — | 54 / E06 | — |
| 39 / E07 | ROB Allow Core 1 Advance | 55 / E07 | — |
| 40 / E08 | ROB Allow Core 1 Retreat | 56 / E08 | IMM Core 1 Advance Done |
| 41 / E09 | ROB Allow Core 2 Advance | 57 / E09 | IMM Core 1 Retreat Done |
| 42 / E10 | ROB Allow Core 2 Retreat | 58 / E10 | IMM Core 2 Advance Done |
| 43 / E11 | ROB Allow Mold Close | 59 / E11 | IMM Core 2 Retreat Done |
| 44 / E12 | ROB Robot E-Stop (Reverse Logic) | 60 / E12 | IMM Mold Open End |
| 45 / E13 | ROB Mold Area Safety | 61 / E13 | IMM Eject Retreat Done |
| 46 / E14 | ROB Robot Manual | 62 / E14 | IMM Eject Advance Done |
| 47 / E15 | ROB Eject Retreat Safety | 63 / E15 | IMM Injection Auto |
| 48 / E16 | ROB Eject Advance Safety | 64 / E16 | IMM Mold Close End |
IO Extension Board · Euro 12 Robot
| Ext DI | Signal | Ext DO | Signal |
|---|---|---|---|
| 33 / E01 | — | 49 / E01 | — |
| 34 / E02 | — | 50 / E02 | — |
| 35 / E03 | — | 51 / E03 | — |
| 36 / E04 | — | 52 / E04 | — |
| 37 / E05 | — | 53 / E05 | — |
| 38 / E06 | — | 54 / E06 | — |
| 39 / E07 | — | 55 / E07 | — |
| 40 / E08 | — | 56 / E08 | — |
| 41 / E09 | — | 57 / E09 | — |
| 42 / E10 | — | 58 / E10 | — |
| 43 / E11 | ROB Allow Mold Close | 59 / E11 | — |
| 44 / E12 | ROB Robot E-Stop (Reverse Logic) | 60 / E12 | IMM Mold Open End |
| 45 / E13 | ROB Mold Area Safety | 61 / E13 | IMM Eject Retreat Done |
| 46 / E14 | ROB Robot Manual | 62 / E14 | IMM Eject Advance Done |
| 47 / E15 | ROB Eject Retreat Safety | 63 / E15 | IMM Injection Auto |
| 48 / E16 | ROB Eject Advance Safety | 64 / E16 | IMM Mold Close End |
Standard Configuration List
- Estun 3100A Host + T10, 2 groups of Blow Valves
- No Nozzle Air Valve
- Core (Standard / Reserved): 1 group / 1 group
- E-Stop and Safety Doors use electrical wiring, not output points.
- For Estun hosts, the IO extension board point layout is the same for Euro 12 / 67; actual electrical wiring differs.