IV5200_270-600_SP6_SCT_Standard_Euro12_Euro67
Source file: IV5200_270-600_SP6_SCT_Standard_Euro12_Euro67_20260501. Configuration: DI48 / DO64 / AI6 / AO8 + E502.
Main Board IO
Digital Input DI (48 points)
| Point | Name |
|---|---|
| DI1 | Mechanical Safety Detection |
| DI2 | Safety Door 2 (NO) |
| DI3 | Core A Advance End |
| DI4 | Core A Retreat End |
| DI5 | Core B Advance End |
| DI6 | Core B Retreat End |
| DI7 | Mold Close End |
| DI8 | Mold Adjust Advance End |
| DI9 | Mold Adjust Retreat End |
| DI10 | — |
| DI11 | Injection Guard |
| DI12 | Ejector Retreat End |
| DI13 | ROB Robot |
| DI14 | Carriage Advance End |
| DI15 | Rear Safety Door (Reverse Logic) (NC) |
| DI16 | Oil Filter Detection |
| DI17 | Screw Speed Detection |
| DI18 | Mold Adjust Photocell |
| DI19 | Detection Photocell 1 |
| DI20 | Thread A Photocell |
| DI21 | Safety Door (Reverse Logic) (NC) |
| DI22~DI23 | — |
| DI24 | Lubrication Detection |
| DI25~DI26 | — |
| DI27 | Safety Door Anti-Collision (Electric Door Reserved) |
| DI28 | Safety Door Open (Electric Door Reserved) |
| DI29 | Electric Recovery Drive Fault |
| DI30~DI48 | — |
Digital Output DO (64 points)
| Point | Name |
|---|---|
| DO1 | *Mold Close |
| DO2 | Recovery Linkage |
| DO3 | *Mold Open |
| DO4 | Injection |
| DO5 | Injection Retreat |
| DO6 | Recovery |
| DO7 | Carriage Advance |
| DO8 | Carriage Retreat |
| DO9 | Ejector Advance |
| DO10 | Ejector Retreat |
| DO11 | Core A Advance |
| DO12 | Core A Retreat |
| DO13 | Mold Adjust Advance |
| DO14 | Mold Adjust Retreat |
| DO15 | Core B Advance |
| DO16 | Core B Retreat |
| DO17 | IMM Safety Door |
| DO18 | Recovery Back Pressure |
| DO19 | Blow 1 |
| DO20 | Recovery Zero Back Pressure |
| DO21 | — |
| DO22 | Mold Open Fast |
| DO23 | Alarm |
| DO24 | Valve 1 |
| DO25 | Mold Close Safety |
| DO26 | Auto Light |
| DO27 | Manual Light |
| DO28 | Blow 2 |
| DO29 | Blow 6 |
| DO30 | Blow 7 |
| DO31 | Hopper Cooling (Reserved) |
| DO32 | Valve 2 |
| DO33 | Heater 1 |
| DO34 | Heater 2 |
| DO35 | Heater 3 |
| DO36 | Heater 4 |
| DO37 | Heater 5 |
| DO38 | Heater 6 |
| DO39 | Heater 7 |
| DO40 | Heater 8 |
| DO41 | Heater 9 |
| DO42 | Motor ON |
| DO43 | TC1 Heater ON (Master Heater ON) |
| DO44 | Lubrication |
| DO45 | IMM Robot |
| DO46 | Safety Door Close (Reserved) |
| DO47 | Safety Door Open (Reserved) |
| DO48 | Blow 8 |
| DO49 | Eject Retreat Setting (Drip Tube Machine Only) |
| DO50 | Recovery Linkage |
| DO51 | Masterbatch Machine |
| DO52 | Lubrication Switch |
| DO53 | Oil Temp Cooling (Reserved) |
| DO54 | Blow 3 |
| DO55 | Blow 4 |
| DO56 | Blow 5 |
| DO57 | Injection 2 |
| DO58 | Valve 3 (Reserved) |
| DO59 | Valve 4 (Reserved) |
| DO60 | Recovery (Oil Motor Reserved) |
| DO61~DO64 | — |
Analog AI / AO
| Point | Name |
|---|---|
| AI1 | Injection |
| AI2 | Mold Open/Close |
| AI3 | Ejector |
| AI4~AI6 | — |
| AO1 | — |
| AO2 | Electric Recovery |
| AO3 | Proportional Back Pressure |
| AO4 | Proportional Valve |
| AO5~AO8 | — |
Temperature TI (6-zone Input)
| Point | Note |
|---|---|
| TI0 | Oil Temp |
| TI1~TI9 | — |
IO Extension Board · Euro 67 Robot
| Ext DI | Signal | Ext DO | Signal |
|---|---|---|---|
| 49 / E01 | — | 65 / E01 | — |
| 50 / E02 | — | 66 / E02 | — |
| 51 / E03 | — | 67 / E03 | — |
| 52 / E04 | — | 68 / E04 | — |
| 53 / E05 | — | 69 / E05 | — |
| 54 / E06 | — | 70 / E06 | — |
| 55 / E07 | ROB Allow Core 1 Advance | 71 / E07 | — |
| 56 / E08 | ROB Allow Core 1 Retreat | 72 / E08 | IMM Core 1 Advance Done |
| 57 / E09 | ROB Allow Core 2 Advance | 73 / E09 | IMM Core 1 Retreat Done |
| 58 / E10 | ROB Allow Core 2 Retreat | 74 / E10 | IMM Core 2 Advance Done |
| 59 / E11 | ROB Allow Mold Close | 75 / E11 | IMM Core 2 Retreat Done |
| 60 / E12 | ROB Robot E-Stop (Reverse Logic) | 76 / E12 | IMM Mold Open End |
| 61 / E13 | ROB Mold Area Safety | 77 / E13 | IMM Eject Retreat Done |
| 62 / E14 | ROB Robot Manual | 78 / E14 | IMM Eject Advance Done |
| 63 / E15 | ROB Eject Retreat Safety | 79 / E15 | IMM Injection Auto |
| 64 / E16 | ROB Eject Advance Safety | 80 / E16 | IMM Mold Close End |
IO Extension Board · Euro 12 Robot
| Ext DI | Signal | Ext DO | Signal |
|---|---|---|---|
| 49 / E01 | — | 65 / E01 | — |
| 50 / E02 | — | 66 / E02 | — |
| 51 / E03 | — | 67 / E03 | — |
| 52 / E04 | — | 68 / E04 | — |
| 53 / E05 | — | 69 / E05 | — |
| 54 / E06 | — | 70 / E06 | — |
| 55 / E07 | — | 71 / E07 | — |
| 56 / E08 | — | 72 / E08 | — |
| 57 / E09 | — | 73 / E09 | — |
| 58 / E10 | — | 74 / E10 | — |
| 59 / E11 | ROB Allow Mold Close | 75 / E11 | — |
| 60 / E12 | ROB Robot E-Stop (Reverse Logic) | 76 / E12 | IMM Mold Open End |
| 61 / E13 | ROB Mold Area Safety | 77 / E13 | IMM Eject Retreat Done |
| 62 / E14 | ROB Robot Manual | 78 / E14 | IMM Eject Advance Done |
| 63 / E15 | ROB Eject Retreat Safety | 79 / E15 | IMM Injection Auto |
| 64 / E16 | ROB Eject Advance Safety | 80 / E16 | IMM Mold Close End |
- E-Stop and Safety Doors use electrical wiring, not output points.
- For Estun hosts, the IO extension board point layout is the same for Euro 12 / 67; actual electrical wiring differs.